Longton Audi Repairs: Fuel Pump Installation

If you've been involved in an accident and your Audi won't start then an inertia switch may have tripped the power supply to the fuel pump and need resetting

Fuel delivery into the Audi fuel injectors is normally controlled by an electronic control unit (ECU) with inbuilt safety features to switch off the fuel pump in the event of an accident or fault

Metallic particles in the fuel filter could be caused by a faulty or worn out fuel pump and may eventually block the fuel injectors and require a very expensive repair

With Electronic Fuel Injection Systems (EFI); the fuel pump is often located within the fuel tank so that the tank can be pressurised to pump fuel to the engine rather than require a vacuum pump at the engine that could pull in air and cause erratic engine running

Audi fuel injection engines require fuel to be pumped under pressure from the fuel tank to the engine fuel injection system

Audi Fuel Pump Faulty or Stopped Working?
Get an estimate to fit a replacement Audi Fuel pump using the simple enquiry form

It is possible for current ECU technology to monitor oil pressure and detect a sudden drop or no oil pressure and switch off the fuel pump to prevent the engine seizing, hence it may not always be a problem with the Audi fuel pump

Fitting the fuel pump within the Audi fuel tank below the fuel level allows the liquid fuel to actually keep the pump cool and reduces the risk of the fuel igniting accidentally

Audi Longton Servicing - Synthetic Oil & Audi Filters

Audi Lubrication System Services Longton

Audi Body Panels
Replacement Audi panels fitted & sprayed to match - Light Audi Panel damage repairs

Audi Timing Belt - Audi Cambelt
Audi Timing Belts replaced as part of a planned Audi service or if the Timing Belt on your Audi has snapped then a full engine inspection for valve & piston damage

Audi Oil Change & Filters Replaced
Audi Air filters, pollen filters; oil filter & fuel filter replaced, engine oil changed - Multigrade or Synthetic oils

Audi Tyres
Steel wheels, alloy wheels and tyres repaired and replaced with cheap tyres, run-flat tyres or low profile & performance tyres depending upon your budget and driving requirements. Part-Worn tyres may be available for your Audi model

Audi Gearboxes
Audi Manual & Automatic gearbox servicing & repair - Fitting a new or reconditioned Audi gearbox

Audi EGR Valves
Replacement Audi EGR valves - ensure the exhaust gas recirculation system is functioning correctly on your Audi - The EGR valve helps your Audi burn fuel more efficiently by recirculating a portion the exhaust gas through combustion chamber and helps reduce Audi engine emissions; a broke or sticking EGR valve can be the cause of an MOT failure due to excessive emissions

Audi Brakes
Routine Audi servicing, replacement Audi brake pads & discs fitted, Audi hydraulic pipework and joints inspected, repaired or replaced for a complete braking system overhaul

Audi Starter Motors
Replacement Audi Starter motors installed

Audi Clutches
Audi clutch repairs Longton - Checking for leaks and repairing-replacing the clutch master-slave cylinder and fitting a new Audi Clutch kit

Audi Fuel Pumps
Often replaced at a milestone service if the fuel pump is operated by the Timing belt

Audi Alternators
Replacement Audi alternators fitted

Audi Electrical Components
Audi electrical faults repaired using Audi OEM components - Audi sensors checked e.g. Lambda sensors, air flow meters etc

Audi Performance Spares
OEM Audi parts fitted or replaced with alternative performance parts

Audi Suspension System
Audi replacement shock absorbers & springs fitted for front or rear suspension problems, broken springs. Custom suspension systems installed, lowering springs fitted

Audi Cooling System
Replacement Audi radiators fitted, cooling system pipework inspected for leaks and cooling fluid replaced to keep your Audi engine at its optimal operating temperature

Audi Autoelectrics
Audi electrical faults diagnosed - OBD fault finding - Audi engine fault codes checked & service lights reset - ECU problems, key coding and CANBUS systems checked

Audi Engines
Audi Engine repairs, cylinder head skimming, valves & pistons

Audi Paint Resprays
Paint resprays for minor scratch damage to the Audi paint surface or coating; Custom paintwork to make your Audi different using metallic paints, pearlescent pigments or company colours.

Audi Exhausts
Audi Engine manifolds, Front box, Back box, catalytic converter and exhaust pipes for Audi Exhausts fitted & welded

Longton Brake Fitting - New Disc Brakes & Pads

Audi brakes can last for thousand of miles depending on use and regular service

The hydraulic brake fluid is a non-compressible liquid so braking pressure is transferred via the brake pipes to the wheels and operates a slave cylinder piston that forces the brake pads against a brake drum or brake disc

The brake pedal controls the Master Cylinder (a fluid filled hydraulic piston) that transfers stopping power to the brakes

Modern Audi braking systems use hydraulic links to transfer stopping power

The enforced contact between the brake pads and brake drum or brake disc increases friction to slow down or stop the vehicle

Braking increases hydraulic brake fluid pressure

Audi Disc Brakes and Drum Brake Systems

Drum Brakes, if fitted, are usually found on Audi rear wheels

Audi disc brakes have a pair of high friction brake pads mounted either side of a brake disc

In hydraulic braking systems, braking pressure operates a slave cylinder

Drum Brakes are an older system than Audi disc brakes and use two half moon shaped brake shoes that move outwards during use to apply a frictional stopping force against the inside of a brake drum

Hydraulic braking pressure forces a brake calliper to press the brake pads against the disc to apply the necessary stopping force

Audi Brake Servicing - Audi Brake Discs and Pads

If the Audi brake discs warp then they should be replaced immediately

The brake pads on your Audi should wear first

Audi Brakes will safely function correctly without the need for replacement for many thousands of miles

if the Audi brakes overheat and are allowed to cool with pressure still applied for m the brake pads/shoes then it is possible for the disc to warp.

Audi brake discs will wear and need replacing eventually and should be inspected for pitting

Audi Brake Inspection Elements

Lubricate Hand Brake Linkages

General brake disc condition

Brake calliper operation

Handbrake function and travel

ABS warning light operation

Replace Brake Fluid if necessary

And carry out the following maintenance of your Audi braking system:-

Correct brake pad movement and level of wear

Adjust handbrake

Brake drum condition

Hand brake linkage condition

Top Up Brake and Clutch Fluid Levels or

Wheel cylinder condition

Auxiliary handbrake shoes where appropriate

Hydraulic brake pipe fittings and joints for corrosion and leaking

Clean and remove brake dust and loose corrosion and dirt from drums

Brake pipe Condition

Audi Steering System

One of the first signs of a potential problem with your Audi steering system is uneven tyre wear

Common symptoms of Audi steering alignment problems include:-
Vehicle Drift - Your Audi tends to pull left or right when travelling in a straight line
Modern Power steering and Drive by Wire Systems do not have the same mechanical linkages between the steering column and drive wheels making it difficult to 'feel' how the steering is performing.

The tyres will need to be replaced much sooner than necessary until the steering rack is adjusted to bring your wheels into correct alignment

The tyre tread is rapidly removed from the inner or outer tyre edge of your front tyres

Your Audi steering inspection can include:-

Correct wheel nut torque to manufacturer's recommendations

Correct Tyre Pressure - inc Spare

Steering Condition

Tyre Condition - inc Spare

Audi Tyre wear and wheel alignment

Wheel Bearings for wear - play or noise

Correct wheel balance, including spare

Steering Linkages for wear and corrosion

Steering Rack Gaiter condition

Power Steering Reservoir Levels and Top Up

Audi Services: Brakes Servicing and Repair

Brakes can last for thousand of miles depending on use and regular service.

The enforced contact between the brake pads and brake drum or brake disc increases friction to slow down or stop the vehicle.

Braking increases hydraulic brake fluid pressure.

The brake pedal is attached the Master Cylinder; a fluid filled hydraulic piston.

The hydraulic brake fluid is a non-compressible liquid so braking pressure is transferred via the brake pipes to the wheels and operates a slave cylinder piston that forces the brake pads against a brake drum or brake disc.

Modern braking systems use hydraulic links to transfer stopping power.

Audi Timing Belt or Cambelt

The toothed belt connecting the engine crankshaft to the camshaft is known as the Cambelt or Timing belt

Timing belts must be replaced at a specified manufacturer's interval. The timing belt should also be inspected regularly and replaced immediately if there is any evidence of cracking or fraying cuts or excessive wear

The Timing Belt synchronizes the camshaft to the crankshaft position ensuring the valves open and close at the correct time in relation to the piston. Some vehicles use a cam chain in place of the belt or a timing gear system instead

If the timing belt snaps it will most probably cause serious engine damage. The camshaft stops turning with some of the valves left in the open position. In a Free Running Engine there is enough clearance between a fully open valve and the piston head to avoid serious damage. In an Interference Engine there is no clearance and the engine relies upon accurate timing to keep the valves and piston head separated. With a broken timing belt; the inertia helps the crankshaft to rotate freely forcing the pistons to strike the open valves resulting in damaged valves, pistons, and possibly even damage to the cylinder head

Since Audi Timing Belts are hidden inside the engine they tend to be forgotten when purchasing a used Audi

Often it is prudent to replace a combination of items associated with the timing system. Most of the needed Audi parts can be obtained as timing kits containing the appropriate timing components; such as: Audi timing belt
timing belt tensioners
timing belt tensioner idler roller
front lower crank shaft seal
water pump gasket

High compression diesel engines are normally interference engines

Generally Audi belts should be replaced every 60,000 miles or less. So, if you have just bought a secondhand Audi that has 40,000 to 80,000 miles then it is important to know if the timing belt has been replaced or needs replacing. Check the Audi Owner's manual for your model for the recommended changing frequency

Longton Replacement Audi Clutch

When the clutch is dis-engaged the clamping force is removed so the clutch disc spins with the flywheel and no power is transmitted

The centre of the clutch disc has a spline pattern that matches splines on the power input shaft of the transmission system

Audi Clutch failure often occurs when one or more of the high friction surface materials wears out on the disc. Even when the pressure plate is engaged and a clamping force is applied, there is no longer sufficient friction to transmit power without the clutch slipping. Normally the Audi clutch disc and pressure plate are replaced. Replacing the Audi Clutch is a major operation and it is sometimes advisable to replace a number of items, often supplied as a Audi Clutch kit:-
Audi clutch disc
pressure plate
release bearing
pilot bearing - bushing (when required)
internal Audi clutch slave cylinder

Engaging the clutch forces the clutch against the flywheel transmitting power from the crankshaft to the transmission shaft

The Audi clutch disc is, not surprisingly, a disc with each side covered in a high friction material. It is designed to engage with the high-friction surfaces of the pressure plate and flywheel. It is also designed to transmit power to theAudi transmission system

Disengaging the clutch acts on heavy-duty release springs to isolate the pressure plate so that the disc is no longer pressed against the flywheel

The pressure plate comprises heavy-duty release springs, a metal pressure ring acting as a high friction surface to interact with the clutch disc, a thrust ring (or thrust fingers) for the release bearing, and release levers

Audi Engine Efficiency - Fuel Injection

Audi Fuel Injection
Fuel injection systems mix fuel with just the right amount of air for optimal combustion & energy release in an internal combustion engine

Audi Re-Mapping Longton
The Audi ECU can be replaced with a programmable ECU or re-mapped to electronically alter the engine performance characteristics

EFI - Electronic Fuel Injection
The Audi fuel injection system is controlled by a mini-computer or Electronic Control Unit (ECU) that assimilates data from a series of temperature sensors and oxygen or lambda sensors providing feedback to help optimise fuel efficiency and power under a variety of conditions

Audi Engine Mapping
The Audi ECU controlling engine performance is pre-programmed with software containing embedded data on engine performance for different combinations of engine speed and acceleration

LPG Petrol or Diesel Metering
Fuel Injection systems have replaced carburetors for the accurate mixing and delivering of petrol, lpg or diesel fuel in modern Audi vehicles

Audi Maintenance - Oil & Filter Change Longton

Oil Change Frequency
The mechanics rule of thumb with traditional multigrade engine oils used to be "change the oil every 3000 miles" but many vehicle manufacturers indicate 5000 to 7000 miles. Initially, follow the Audi recommended oil change guidelines to ensure you validate your warranty.

Oil & Filter Change
A new Audi oil filter and oil change shouldn't need a specialist Audi engineer and is minimal compared to the cost of an Engine Rebuild; with regular maintenance and routine servicing working out cheaper than disaster recover when your Audi engine fails

Anti Oxidants
Preventing internal engine oxidation in your Audi motor is the job of sacrificial anti-oxidants present in the lubricating oil; Anti oxidants are sacrificed to protect your engine and will eventually be depleted making it necessary to change your oil regularly

Oil Composition
Engine Lubricating Oil is composed of hundreds of chemicals; some can interact chemically, polymerise, oxidise and break down with the extreme conditions of temperature & shear forces pulling the oil molecules apart in your Audi engine thus, changing the lubrication properties.

Moisture Scavengers - Detergents - Acidity Regulators
Moisture scavengers, detergents and acidity regulators prevent all kinds of contaminants degrading and abrading the internal moving surfaces of your Audi engine minimising the effects that water, particles, and fuel combustion residus can have on Audi performance
Once they have absorbed the maximum amount of water and other contaminants; the risk of corrosion and failure in your in your Audi engine increases

Oil Change Masterclass
Keep a small amount of the engine oil used in your next oil change in a sealed container; then when you check your oil level with the dipstick you can compare the lubricity or lubricating properties of the oil against your fresh oil:- If the oil on the dipstick seems thin compared to your reference oil sample; it may be time to get an oil change to keep your Audi running smoothly

Synthetic Oil Change - Longton
Modern synthetic oils can last longer than old petroleum based multigrades because they are more inert with a laboratory designed molecular structure and fewer natural catalytic impurities that increase oil breakdown compared to the cheaper engine oils

Audi Exhaust Fitting Longton

The Audi exhaust system allows poisonous gases from the fuel combustionto vent into the atmoshpere away from the driver and cabin

Corroded exhaust pipes allow fumes and noise to escape; increasing the risk of poisonous carbon monoxide entering the cabin and significantly increasing noise making detection an easy task

The exhaust pipework helps muffle and deaden the noise from the fuel combustion process

Explosions from the instantaneous ignition of the compressed fuel and air igniting in the combustion chamber creat a lot of noise that needs to be silenced in the urban environment