Replacement Saab Clutch Longton

If there is a slight leak in the hydraulic pipework or; more likely; the seals on the master or slave clutch cylinder then you may find it difficult to change gears as the clutch does not fully disengage

If there is plenty of torque and the clutch appears to be slipping; then it may be that the high friction surface has worn away and a new Saab clutch is needed

Saab Hydraulic Clutch – Master Cylinder - Slave Cylinder
Operating the clutch pedal actuates a hydraulic piston linked to the clutch pedal
This increases fluid pressure to operate a secondary piston that engages-disengages the Saab clutch plates

Your Saab clutch connects and disconnects the engine from the gearbox to allow for the smooth transition from one gear to the next and allows the vehicle to remain stationary with the engine running.

Does your Saab need a new clutch?
Use our form to request a replacement Saab clutch, slave or master cyclinder

Clutch wear can make it difficult to pull away from a cold engine start without the engine juddering

The Saab clutch plate has a high friction coating on both sides and is fitted between the Saab engine flywheel and a spring loaded pressure plate
The clutch is disengaged in manual gearbox versions when the clutch pedal is depressed.

The clutch forms a mechanical linkage to transfer power from the engine/gearbox to the driving wheels of your Saab

Saab Clutch, Master & Slave Cylinder Repairs Longton

Longton: Saab Clutch Fitting

Saab Tyres
Steel wheels, alloy wheels and tyres repaired and replaced with cheap tyres, run-flat tyres or low profile & performance tyres depending upon your budget and driving requirements. Part-Worn tyres may be available for your Saab model

Saab Body Panels
Replacement Saab panels fitted & sprayed to match - Light Saab Panel damage repairs

Saab Autoelectrics
Saab electrical faults diagnosed - OBD fault finding - Saab engine fault codes checked & service lights reset - ECU problems, key coding and CANBUS systems checked

Saab Starter Motors
Replacement Saab Starter motors installed

Saab Suspension System
Saab replacement shock absorbers & springs fitted for front or rear suspension problems, broken springs. Custom suspension systems installed, lowering springs fitted

Saab Alternators
Replacement Saab alternators fitted

Saab Cooling System
Replacement Saab radiators fitted, cooling system pipework inspected for leaks and cooling fluid replaced to keep your Saab engine at its optimal operating temperature

Saab Timing Belt - Saab Cambelt
Saab Timing Belts replaced as part of a planned Saab service or if the Timing Belt on your Saab has snapped then a full engine inspection for valve & piston damage

Saab Performance Spares
OEM Saab parts fitted or replaced with alternative performance parts

Saab EGR Valves
Replacement Saab EGR valves - ensure the exhaust gas recirculation system is functioning correctly on your Saab - The EGR valve helps your Saab burn fuel more efficiently by recirculating a portion the exhaust gas through combustion chamber and helps reduce Saab engine emissions; a broke or sticking EGR valve can be the cause of an MOT failure due to excessive emissions

Saab Gearboxes
Saab Manual & Automatic gearbox servicing & repair - Fitting a new or reconditioned Saab gearbox

Saab Clutches
Saab clutch repairs Longton - Checking for leaks and repairing-replacing the clutch master-slave cylinder and fitting a new Saab Clutch kit

Saab Oil Change & Filters Replaced
Saab Air filters, pollen filters; oil filter & fuel filter replaced, engine oil changed - Multigrade or Synthetic oils

Saab Fuel Pumps
Often replaced at a milestone service if the fuel pump is operated by the Timing belt

Saab Engines
Saab Engine repairs, cylinder head skimming, valves & pistons

Saab Exhausts
Saab Engine manifolds, Front box, Back box, catalytic converter and exhaust pipes for Saab Exhausts fitted & welded

Saab Paint Resprays
Paint resprays for minor scratch damage to the Saab paint surface or coating; Custom paintwork to make your Saab different using metallic paints, pearlescent pigments or company colours.

Saab Brakes
Routine Saab servicing, replacement Saab brake pads & discs fitted, Saab hydraulic pipework and joints inspected, repaired or replaced for a complete braking system overhaul

Saab Electrical Components
Saab electrical faults repaired using Saab OEM components - Saab sensors checked e.g. Lambda sensors, air flow meters etc

Saab Service - Saab Braking Systems - Hydrauic Brake Maintenance

The hydraulic brake fluid is a non-compressible liquid so braking pressure is transferred via the brake pipes to the wheels and operates a slave cylinder piston that forces the brake pads against a brake drum or brake disc

The enforced contact between the brake pads and brake drum or brake disc increases friction to slow down or stop the vehicle

The brake pedal controls the Master Cylinder (a fluid filled hydraulic piston) that transfers stopping power to the brakes

Modern Saab braking systems use hydraulic links to transfer stopping power

Saab brakes can last for thousand of miles depending on use and regular service

Braking increases hydraulic brake fluid pressure

Longton Saab Brake Repairs

Saab disc brakes have a pair of high friction brake pads mounted either side of a brake disc

In hydraulic braking systems, braking pressure operates a slave cylinder

Drum Brakes are an older system than Saab disc brakes and use two half moon shaped brake shoes that move outwards during use to apply a frictional stopping force against the inside of a brake drum

Drum Brakes, if fitted, are usually found on Saab rear wheels

Hydraulic braking pressure forces a brake calliper to press the brake pads against the disc to apply the necessary stopping force

Saab Brake Servicing - Saab Brake Maintenance & Parts Replacement

If the Saab brake discs warp then they should be replaced immediately

Saab brake discs will wear and need replacing eventually and should be inspected for pitting

Saab Brakes will safely function correctly without the need for replacement for many thousands of miles

The brake pads on your Saab should wear first

if the Saab brakes overheat and are allowed to cool with pressure still applied for m the brake pads/shoes then it is possible for the disc to warp.

Saab Brake Servicing & Inspection Longton

Handbrake function and travel

ABS warning light operation

Clean and remove brake dust and loose corrosion and dirt from drums

Correct brake pad movement and level of wear

And carry out the following maintenance of your Saab braking system:-

Lubricate Hand Brake Linkages

Brake calliper operation

Top Up Brake and Clutch Fluid Levels or

Auxiliary handbrake shoes where appropriate

Brake drum condition

Hydraulic brake pipe fittings and joints for corrosion and leaking

Replace Brake Fluid if necessary

Hand brake linkage condition

Brake pipe Condition

Adjust handbrake

Wheel cylinder condition

General brake disc condition

Saab Steering - Steering System Inspection

Common symptoms of Saab steering alignment problems include:-
Vehicle Drift - Your Saab tends to pull left or right when travelling in a straight line
Modern Power steering and Drive by Wire Systems do not have the same mechanical linkages between the steering column and drive wheels making it difficult to 'feel' how the steering is performing.

One of the first signs of a potential problem with your Saab steering system is uneven tyre wear

The tyre tread is rapidly removed from the inner or outer tyre edge of your front tyres

The tyres will need to be replaced much sooner than necessary until the steering rack is adjusted to bring your wheels into correct alignment

Saab steering inspections:-

Wheel Bearings for wear - play or noise

Steering Linkages for wear and corrosion

Correct wheel nut torque to manufacturer's recommendations

Power Steering Reservoir Levels and Top Up

Saab Tyre wear and wheel alignment

Steering Condition

Correct Tyre Pressure - inc Spare

Steering Rack Gaiter condition

Correct wheel balance, including spare

Tyre Condition - inc Spare

Saab Brake Servicing: Brake Discs, Pads & Hydraulics

Brakes can last for thousand of miles depending on use and regular service.

Modern braking systems use hydraulic links to transfer stopping power.

The brake pedal is attached the Master Cylinder; a fluid filled hydraulic piston.

The hydraulic brake fluid is a non-compressible liquid so braking pressure is transferred via the brake pipes to the wheels and operates a slave cylinder piston that forces the brake pads against a brake drum or brake disc.

Braking increases hydraulic brake fluid pressure.

The enforced contact between the brake pads and brake drum or brake disc increases friction to slow down or stop the vehicle.

Saab Replacement Timing Belt or Cambelt Longton

Often it is prudent to replace a combination of items associated with the timing system. Most of the needed Saab parts can be obtained as timing kits containing the appropriate timing components; such as: Saab timing belt
timing belt tensioners
timing belt tensioner idler roller
front lower crank shaft seal
water pump gasket

High compression diesel engines are normally interference engines

If the timing belt snaps it will most probably cause serious engine damage. The camshaft stops turning with some of the valves left in the open position. In a Free Running Engine there is enough clearance between a fully open valve and the piston head to avoid serious damage. In an Interference Engine there is no clearance and the engine relies upon accurate timing to keep the valves and piston head separated. With a broken timing belt; the inertia helps the crankshaft to rotate freely forcing the pistons to strike the open valves resulting in damaged valves, pistons, and possibly even damage to the cylinder head

The Timing Belt synchronizes the camshaft to the crankshaft position ensuring the valves open and close at the correct time in relation to the piston. Some vehicles use a cam chain in place of the belt or a timing gear system instead

Timing belts must be replaced at a specified manufacturer's interval. The timing belt should also be inspected regularly and replaced immediately if there is any evidence of cracking or fraying cuts or excessive wear

The toothed belt connecting the engine crankshaft to the camshaft is known as the Cambelt or Timing belt

Since Saab Timing Belts are hidden inside the engine they tend to be forgotten when purchasing a used Saab

Generally Saab belts should be replaced every 60,000 miles or less. So, if you have just bought a secondhand Saab that has 40,000 to 80,000 miles then it is important to know if the timing belt has been replaced or needs replacing. Check the Saab Owner's manual for your model for the recommended changing frequency

Saab Fuel Injection

LPG Petrol or Diesel Metering
Fuel Injection systems have replaced carburetors for the accurate mixing and delivering of petrol, lpg or diesel fuel in modern Saab vehicles

EFI - Electronic Fuel Injection
The Saab fuel injection system is controlled by a mini-computer or Electronic Control Unit (ECU) that assimilates data from a series of temperature sensors and oxygen or lambda sensors providing feedback to help optimise fuel efficiency and power under a variety of conditions

Saab Re-Mapping Longton
The Saab ECU can be replaced with a programmable ECU or re-mapped to electronically alter the engine performance characteristics

Saab Engine Mapping
The Saab ECU controlling engine performance is pre-programmed with software containing embedded data on engine performance for different combinations of engine speed and acceleration

Saab Fuel Injection
Fuel injection systems mix fuel with just the right amount of air for optimal combustion & energy release in an internal combustion engine

Saab Engine Oil Change

Synthetic Oil Change - Longton
Modern synthetic oils can last longer than old petroleum based multigrades because they are more inert with a laboratory designed molecular structure and fewer natural catalytic impurities that increase oil breakdown compared to the cheaper engine oils

Oil Composition
Engine Lubricating Oil is composed of hundreds of chemicals; some can interact chemically, polymerise, oxidise and break down with the extreme conditions of temperature & shear forces pulling the oil molecules apart in your Saab engine thus, changing the lubrication properties.

Oil & Filter Change
A new Saab oil filter and oil change shouldn't need a specialist Saab engineer and is minimal compared to the cost of an Engine Rebuild; with regular maintenance and routine servicing working out cheaper than disaster recover when your Saab engine fails

Oil Change Frequency
The mechanics rule of thumb with traditional multigrade engine oils used to be "change the oil every 3000 miles" but many vehicle manufacturers indicate 5000 to 7000 miles. Initially, follow the Saab recommended oil change guidelines to ensure you validate your warranty.

Oil Change Masterclass
Keep a small amount of the engine oil used in your next oil change in a sealed container; then when you check your oil level with the dipstick you can compare the lubricity or lubricating properties of the oil against your fresh oil:- If the oil on the dipstick seems thin compared to your reference oil sample; it may be time to get an oil change to keep your Saab running smoothly

Anti Oxidants
Preventing internal engine oxidation in your Saab motor is the job of sacrificial anti-oxidants present in the lubricating oil; Anti oxidants are sacrificed to protect your engine and will eventually be depleted making it necessary to change your oil regularly

Moisture Scavengers - Detergents - Acidity Regulators
Moisture scavengers, detergents and acidity regulators prevent all kinds of contaminants degrading and abrading the internal moving surfaces of your Saab engine minimising the effects that water, particles, and fuel combustion residus can have on Saab performance
Once they have absorbed the maximum amount of water and other contaminants; the risk of corrosion and failure in your in your Saab engine increases

Longton Exhaust Fitting Saab

The exhaust pipework helps muffle and deaden the noise from the fuel combustion process

The Saab exhaust system allows poisonous gases from the fuel combustionto vent into the atmoshpere away from the driver and cabin

Corroded exhaust pipes allow fumes and noise to escape; increasing the risk of poisonous carbon monoxide entering the cabin and significantly increasing noise making detection an easy task

Explosions from the instantaneous ignition of the compressed fuel and air igniting in the combustion chamber creat a lot of noise that needs to be silenced in the urban environment

Saab Clutch Fitting Longton

The Saab clutch disc is, not surprisingly, a disc with each side covered in a high friction material. It is designed to engage with the high-friction surfaces of the pressure plate and flywheel. It is also designed to transmit power to theSaab transmission system

The centre of the clutch disc has a spline pattern that matches splines on the power input shaft of the transmission system

Saab Clutch failure often occurs when one or more of the high friction surface materials wears out on the disc. Even when the pressure plate is engaged and a clamping force is applied, there is no longer sufficient friction to transmit power without the clutch slipping. Normally the Saab clutch disc and pressure plate are replaced. Replacing the Saab Clutch is a major operation and it is sometimes advisable to replace a number of items, often supplied as a Saab Clutch kit:-
Saab clutch disc
pressure plate
release bearing
pilot bearing - bushing (when required)
internal Saab clutch slave cylinder

Disengaging the clutch acts on heavy-duty release springs to isolate the pressure plate so that the disc is no longer pressed against the flywheel

When the clutch is dis-engaged the clamping force is removed so the clutch disc spins with the flywheel and no power is transmitted

Engaging the clutch forces the clutch against the flywheel transmitting power from the crankshaft to the transmission shaft

The pressure plate comprises heavy-duty release springs, a metal pressure ring acting as a high friction surface to interact with the clutch disc, a thrust ring (or thrust fingers) for the release bearing, and release levers